SPONSORS
2024 ICRBE EXPO |
Current Page: 1 of 1
Results 1 - 19 of 19
3 years ago
James Rice
Kent forgive me, but I use my computer to pay bills and but rod components....What you suggested for uploading a photo is Greek to me...Can I send the photo to your email address?
Forum: rodboard 3 years ago
James Rice
My friend who's the same age as me (62) Had a grandfather that died 25 years ago who was a rod builder. My friend gave me some blanks he found....They seem to be all fiberglass, but they are stout pool cues....and why can't I post a photo here?
Forum: rodboard 10 years ago
James Rice
4. Drying motor
Hi guys,
I'm getting tired of my cheap drying motors burning out and or shaft becomes loose.
I'm wanting to buy a Dayton gearmotor. Any suggestions or advice on RPM?
I'm looking at a 6rpm or 18rpm
Thanks in advance
Forum: rodboard 10 years ago
James Rice
I built a NOS 8-17 Shikari 7'6" with AT micro guides for inshore trout fishing and have brought in Reds, Jack and even a over sized snook. The guides are great for braid. I use 10 lb Power Pro and casts great. I never get many wind knots, always close the reel manually. I'm making another I like the guides that much. Like everything else they will be a test of time
Forum: rodboard 10 years ago
James Rice
I came across an old gent who removes his used guides and places them in white vinegar for 24 hrs.
I tried this to some old Fuji dbl foots guides and they look great with just rubbing gently. I'm wondering about structurally safe?
Opinions?
Thanks
Forum: rodboard 10 years ago
James Rice
Thanks. The blanks I have are BPOS800XHC(B)
Very lightweight for such a workhorse. I'd like to find out more about them
Forum: rodboard 10 years ago
James Rice
9. Kencor blank
I've come into 3 Kecor blanks 30-80wt 8' one piece
Just wondering if they are worth putting top of the line guides, reel seat etc on them?
Forum: rodboard 10 years ago
James Rice
My writing is terrible with pen and acrylic ink
I checked this site and a lot of sponsors to your left for lettering decals?
There has to be letter decals somewhere for poor penmanship like mine :) Thx!!
Forum: rodboard 10 years ago
James Rice
Dry wall mesh tape.
You can get the epoxy all the way to the blank through the mesh.
Have had no problems and it's cheap
Tight lines !
Forum: rodboard 10 years ago
James Rice
I Just finished wrapping a 6.6' MHX blank with Amtek Microwaves
Tip of spool to furthest point on MW guide 20 1/2"
Trans guide 30 1/2"
running guide 39 7/8"
Running guides the rest of the way are not so critical. Just these first 3
Tight Lines
Forum: rodboard 10 years ago
James Rice
Thanks guys
BTW: Sometimes I use drywall tape on my butt wraps. Makes a nice diamond pattern covered with metallic thread
Forum: rodboard 10 years ago
James Rice
Well I guess these wont come apart :)
Thanks.
It just doesn't "seem" very strong done the way you state.
These blanks (Shikari) are only 1/2-3/8 butts
They look lonely in these aluminum gimbals
Forum: rodboard 10 years ago
James Rice
The extra fine point sharpies are hard not to have blotching...thick/thin areas.
quill pen and I use acetone to clean it. Pens are cheap. buy a few. Some work better than others.
I also use acrylic ink....
Forum: rodboard 10 years ago
James Rice
Night Snapper fishing I free line the chum line..
Installing a butt gimbal on a stout but short ( 6-6.6') graphite blank. 10-25wt
I've been doing it with E-glass pieces inserted in the gimbal with a ferrule inserted inside the E-glass and sand it to fit the graphite blank.
This is very time consuming. I've searched here, but no joy.
There has to be a better way :)
Forum: rodboard 10 years ago
James Rice
First number is ring as suggested above,
Second number is the diameter of the rod tip IE: (4.5) (7.0)
They sell cheap ($6.00) tip gauges on @#$%& if you need it in a hurry
Forum: rodboard 10 years ago
James Rice
Thanks all. I have lots of questions, but will hold off. I have been building for about 1.5 yrs and basically it's been trial and error....Making some nice stuff now and loving it....I'm sure it can get better.
Tight Lines !!
Forum: rodboard 10 years ago
James Rice
I met an old gent that has me doing guide spacing by placing the blank in pvc at a 45 degree angle.
Attaching the guides with thick tube rubber.
running line up the guides and attaching to a 2 pound weight.
reel down and adjust guides to follow arc of the blank.
It has worked really well, but I seem to use a lot of guides. Say up to 9 for a 7.5 blank
See any problems with this method?
Forum: rodboard
Current Page: 1 of 1
|