SPONSORS
2024 ICRBE EXPO |
Results 1 - 30 of 34
12 years ago
Jeff Haley
1. Shop
Here is where I have my wraping lathe set up. My shop is 8' X 16' and this is where the magic is going to happen..LOL
Forum: rodboard 12 years ago
Jeff Haley
4. Tiger Wrap
This one has Black and Yellow under with Red over
Forum: rodboard 12 years ago
Jeff Haley
Thanks Roger
I have a air compresser. I think I'm going to mist the floor with water also
Forum: rodboard 12 years ago
Jeff Haley
You guys have lots of great ideas. I built my hobby building out in the backyard , it's very nice and I have finished it with sheet rock and sprayed texture on the inside. Paint and trimmed every thing out.
I have R 30 in the ceiling and R 14 in the walls. No windows? There is heat and air and a vent that exhaust to the outside.
I got a small vac with the mini brush to clean the rods and the
Forum: rodboard 12 years ago
Jeff Haley
Thank you for all of your input. I found 4 of the M's and two E's in S glass
Forum: rodboard 12 years ago
Jeff Haley
What do you guys use to get the dust off your thread work?
I need to get the dust off between coats of finish and when I take take pictures you can really see the dust on thread in the pictures..
Thanks,
Jeff
Forum: rodboard 12 years ago
Jeff Haley
Spencer Phipps Wrote:
-------------------------------------------------------
> BMB= black mooching/livebait 96= 8 ft 3
> power E glass Same blank used in XCF 803
> Salmon Kwikfish rod. 12 to 30 lb line rating, 3/4
> to 3 oz. lure/bait rating. Blank catalog number is
> now BMB 96 3M.
Thank you Spencer very much
Forum: rodboard 12 years ago
Jeff Haley
That's and idea. I should of thought of that.
The last place you look is Right in front of you.
Forum: rodboard 12 years ago
Jeff Haley
I found this blank in my shop and would like to know the specs on it..
I hope someone has a old catolog to help me out..
Dark Gray blank--
Lamiglas BMB963E
Take a look and see if you know anything about this blank guys..
Thank you very much,
Jeff
Forum: rodboard 12 years ago
Jeff Haley
17. Re: Fuzzy Thread
Thanks guys. Looks like it back to the store.
Forum: rodboard 12 years ago
Jeff Haley
I have a old Fenwick I have rewrapped for a friend and can not find the number any where on the WEB.
It was a factory rod bought back in the late 60/ early 70 and is 5'-11" long and looks to be a 30-40 lb rod.
The numbers I could see look like.....PR60 C.
The serial number is.. K29338
Does anyone have any info for me? That would be great!
Thank you,
Jeff
Forum: rodboard 12 years ago
Jeff Haley
19. Fuzzy Thread
Has anyone came across spools of thread that is all fuzzed up ?
Is there any thing you can do to get the fuzz off you wrap before you put CP or finish on?
Thanks for any help.
Jeff
Forum: rodboard 12 years ago
Jeff Haley
Thanks Bert,
I would like to try on of yours..
I will send you the info..
Thank you very much...
Forum: rodboard 12 years ago
Jeff Haley
Thanks Brandon
I would like to take a look at that.
My e mail address is-
cptn.jeff@comcast.net
Forum: rodboard 12 years ago
Jeff Haley
One last question!!!!
Which program wooks the best to do your lay up for your decal?
Jeff
Forum: rodboard 12 years ago
Jeff Haley
Thanks you very much guys!!
I think I will go with Decal Connection and keep the small business going here in the USA..
Thank you for all your help..
Jeff
Forum: rodboard 12 years ago
Jeff Haley
Tom,
The red was just to much, so I think i'm going to try a yellow.
Have you ever did one with yellow? If so would it help not to use CP on reg. nylon thread?
Thanks again,
Jeff
Forum: rodboard 12 years ago
Jeff Haley
I put down yellow and black on the under wrap with two thick coats of finish over,
Then I wrapped Red A over that and it looked great! But Too RED... Two questions-
If I stay with the red and don't put CP on it will the color be a little less RED?
What if I try Yellow in reg. or NCP over? with or without CP.
The rod is wrapped in Yellow under and Black over with a spirial of black and red
Forum: rodboard 12 years ago
Jeff Haley
Hi Roger,
I want to apply them with the customers name and specs on the fishing rods..
I just thought it would be more cost afficted to print them myself sence they all will be different..
I'm not able to charge them enought to weave there name in there rods so I have just been doing it for my good friends for "0" $$$$
I would like to hear what you thing would work the best
Forum: rodboard 12 years ago
Jeff Haley
I'm wanting to purchase a label maker and would like to know which one I should get?
I know there has to be a few guys that use them here and know what works and what doesn't
Any info you all have would be a big help.
Thank you,
Jeff
Forum: rodboard |