SPONSORS
2024 ICRBE EXPO |
Re: "Wave" guides and "Acid" wraps
Posted by:
Mark Talmo
(---.dsl.lsan03.sbcglobal.net)
Date: September 30, 2016 12:22PM
Thomas, Thank you for your reply. Mr. Martens is the first I’ve heard of using the MicroWave system during tournament fishing. You mentioned his use of a spinning rod which made me reflect on the few bass tour shows I have watched and I cannot remember seeing anyone using a spinning rod, only casting. I would think the MicroWave system would be more effective/noticeable controlling the chaotic coils coming off a spinning reel than the more controlled line coming off a casting reel, so maybe my question of “how many on tour use the MicroWave system” is not really fair. But then, if Mr. Martens is the only one using a spinning rod and utilizes MicroWave guides, that speaks quite well of the system.
Tom, a few post ago within this thread, Norman mentioned how you “alluded to many fishermen are unwilling to try a spiral wrapped rod because of its unconventional look”. That may be the biggest issue with the concept as I know it is (or more precisely was) with me. The need to slightly deflect the line around to the bottom of the blank does not concern me because the very minimal amount of additional line/guide friction is greatly offset by simply getting the guides and line to the bottom of the rod where they will perform optimally. With a conventional casting setup, properly spaced reduction guides will produce a perfect “bullseye” and, theoretically, afford the line coming off the top of the spool a straight path to pass though without touching the guides. It is impossible to direct the line from the top to the bottom of the rod in a straight line unless angle grilling a hole through the rod as suggested by some imbecile earlier. The line must be deflected a minimum of ½ the rod diameter plus the height of the guide foot to bottom of the ring measurement if only one transition guide is used, slightly less if two are used. Or am I ignorant to/missing something? Mark Talmo FISHING IS NOT AN ESCAPE FROM LIFE BUT RATHER A DEEPER IMMERSION INTO IT!!! BUILDING YOUR OWN SIMPLY ENHANCES THE EXPERIENCE. Re: "Wave" guides and "Acid" wraps
Posted by:
Ken Preston
(---.opera-mini.net)
Date: September 30, 2016 12:33PM
Phil =
Some video of spiral wrapped Black Hole tuna rods in action (as well as conventional wrapped rods) [www.youtube.com] Re: "Wave" guides and "Acid" wraps
Posted by:
Mark Talmo
(---.dsl.lsan03.sbcglobal.net)
Date: September 30, 2016 01:15PM
Thanks, Ken. Nice video! But what happens with a big fish on? lol Mark Talmo FISHING IS NOT AN ESCAPE FROM LIFE BUT RATHER A DEEPER IMMERSION INTO IT!!! BUILDING YOUR OWN SIMPLY ENHANCES THE EXPERIENCE. Re: "Wave" guides and "Acid" wraps
Posted by:
John E Powell
(---.dynamic.wnyric.org)
Date: September 30, 2016 01:42PM
Comments deleted Edited 1 time(s). Last edit at 09/30/2016 04:52PM by John E Powell. Re: "Wave" guides and "Acid" wraps
Posted by:
Mel Shimizu
(---.socal.res.rr.com)
Date: September 30, 2016 01:43PM
That video was taken three years ago on a film trip to Puerto Vallarta featuring Black Hole Rods. The show was broadcast on national TV in South Korea. Last year we did a similar trip to PEI with filming by the same crew. There should be some youtube videos of that trip as well as this years trip just ended last week. Re: "Wave" guides and "Acid" wraps
Posted by:
Tom Kirkman
(Moderator)
Date: September 30, 2016 02:43PM
Mark,
You need to tape up a set of guides and do a bit of pondering - I think you'll understand more about the concept once you actually try it. In fact, you can give it a try and get a good idea of what path the line prefers when the rod is under load. Tape up a set of guides per conventional guides-on-top casting rod. But don't tape them down tightly. Make sure the guides are free to move/spin. Now load the rod via a line through the guides and watch what happens. Nearly all the guides will spin to the bottom of the rod, excepting the first one or two which will tend to settle in somewhere between 30 and 160 degrees depending on the height of the reel used. Some folks set up this way and simply wrap the guides in place after allowing them to seek their own position on the rod blank. Others, most probably, will lock down at least the butt guide on top of the rod and proceed from there. ............... Re: "Wave" guides and "Acid" wraps
Posted by:
Lynn Behler
(---.97.252.156.res-cmts.leh.ptd.net)
Date: September 30, 2016 04:15PM
Mark,spiral wraps appear to look strange to a lot of people but they make you look smarter, more in touch, as a builder. One thing though, try the simple spiral first, you may well find it's all you need and to me it's a lot simpler. Lynn Re: "Wave" guides and "Acid" wraps
Posted by:
Mark Talmo
(---.dsl.lsan03.sbcglobal.net)
Date: September 30, 2016 06:21PM
Hold on, guys! I understand and am more than comfortable with the spiral wrap concept and plan on utilizing it on my next build. Excuse me if not making that clear in my previous posts. The only issue I have is the path the line takes while transitioning. John Powell referred to “the ‘natural’ line path” which is correct but completely different from traveling in a “straight path” as stated in another post. In a two dimensional plane the line travels straight while in three dimensions it does not. With a stripper guide on top and the next reduction guide on the bottom with no guides in between, rod loaded or not, I can only assume the line will rub the blank somewhere between the two. I was simply asking for verification in case I misunderstood something.
You guys have been a wealth of information on the subject and I have absorbed it all while appreciating it immensely. Actually, all the information has left me wondering if my limited experience is capable of producing a spiral wrap. From the first rod built, I have understood and am very comfortable with static testing for guide placement, if not considering it a no-brainer. But this Acid wrap is a different animal. I am not scared to do it, but I do not take defeat lightly and need all my ducks in a row, “I’s” dotted and “t’s” crossed, prior to attempting. By the way, Tom, nice Spiral Demo unit. I would not have expected anything less. Mark Talmo FISHING IS NOT AN ESCAPE FROM LIFE BUT RATHER A DEEPER IMMERSION INTO IT!!! BUILDING YOUR OWN SIMPLY ENHANCES THE EXPERIENCE. Re: "Wave" guides and "Acid" wraps
Posted by:
Mel Shimizu
(---.socal.res.rr.com)
Date: September 30, 2016 07:06PM
Mark Talmo Wrote:
------------------------------------------------------- > Hold on, guys! I understand and am more than > comfortable with the spiral wrap concept and plan > on utilizing it on my next build. Excuse me if not > making that clear in my previous posts. The only > issue I have is the path the line takes while > transitioning. John Powell referred to “the > ‘natural’ line path” which is correct but > completely different from traveling in a > “straight path” as stated in another post. In > a two dimensional plane the line travels straight > while in three dimensions it does not. With a > stripper guide on top and the next reduction guide > on the bottom with no guides in between, rod > loaded or not, I can only assume the line will rub > the blank somewhere between the two. I was simply > asking for verification in case I misunderstood > something. > You guys have been a wealth of information on the > subject and I have absorbed it all while > appreciating it immensely. Actually, all the > information has left me wondering if my limited > experience is capable of producing a spiral wrap. > From the first rod built, I have understood and am > very comfortable with static testing for guide > placement, if not considering it a no-brainer. But > this Acid wrap is a different animal. I am not > scared to do it, but I do not take defeat lightly > and need all my ducks in a row, “I’s” dotted > and “t’s” crossed, prior to attempting. > By the way, Tom, nice Spiral Demo unit. I would > not have expected anything less. The line should never touch the blank at any time...even when loaded on a big bend. Re: "Wave" guides and "Acid" wraps
Posted by:
Tom Kirkman
(Moderator)
Date: September 30, 2016 07:41PM
The line needn't rub the blank if you don't want it to. An offset butt guide or a bumper guide will take care of that. It's probably time for you to dive in and start building one, trying different methods and seeing which one most appeals to you. I think much of what has been written here will make a lot more sense once you have one under your belt.
............. Re: "Wave" guides and "Acid" wraps
Posted by:
Mark Talmo
(---.dsl.lsan03.sbcglobal.net)
Date: October 01, 2016 12:55PM
As suggested, possibly the best thing for me is to just jump in and do it. Securing but not affixing the guides to the blank so they can be repositioned and running a line through them to static test, loaded and unloaded, will probably self explain many issues, even for my over worked brain. Are there any specific guides which are better suited for a spiral wrap or can I stay with my go-to KW’s or MN’s?
As always, Thanks to all assisting. Mark Talmo FISHING IS NOT AN ESCAPE FROM LIFE BUT RATHER A DEEPER IMMERSION INTO IT!!! BUILDING YOUR OWN SIMPLY ENHANCES THE EXPERIENCE. Re: "Wave" guides and "Acid" wraps
Posted by:
Lynn Behler
(---.97.252.156.res-cmts.leh.ptd.net)
Date: October 01, 2016 03:29PM
Mark, You might want to invest in the Rodmaker guides CD. I found it to be helpful, and I'm cheap! Lynn Re: "Wave" guides and "Acid" wraps
Posted by:
curtis drumm
(---.hsd1.md.comcast.net)
Date: October 02, 2016 02:46AM
That's where it will shine.
Curt Sorry, only registered users may post in this forum.
|