SPONSORS
2024 ICRBE EXPO |
uplocking reel seat
Posted by:
Bill Ballou
(---.hsd1.tn.comcast.net)
Date: December 18, 2015 11:50AM
Making some up locking fly grips. 2 parts ! how wide should the insert hole be? 2 How deep? I hope many of the reel seats are close in size. I realize that the down locking seat the end can be flat. Thanks for any help. Bill Re: uplocking reel seat
Posted by:
John E Powell
(---.dynamic.wnyric.org)
Date: December 18, 2015 12:00PM
I think there's a bit of variety from seat to seat. Re: uplocking reel seat
Posted by:
Ron Weber
(---.ph.ph.cox.net)
Date: December 18, 2015 12:06PM
Really depends on the manufacturer and the model #. If it is for a Lemke seat, I have all the specs Ron Weber Re: uplocking reel seat
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: December 18, 2015 12:59PM
============== Edited 1 time(s). Last edit at 12/19/2015 01:51PM by roger wilson. Re: uplocking reel seat
Posted by:
Ron Weber
(---.ph.ph.cox.net)
Date: December 18, 2015 01:17PM
I don't guess I understand what the reels have to do with the inlet depth and ID Ron Weber Re: uplocking reel seat
Posted by:
Bill Ballou
(---.hsd1.tn.comcast.net)
Date: December 18, 2015 01:34PM
I should have stated that these will be at my booth at the ICRBE. Custom Fish Grips-split grips airbrushed and epoxied. I thought that a couple of fly handles might be of interest. By the responses I think I will make full wells in down locking. Probably with a rainbow trout theme. This piece should weigh 1 1/2 oz. Thanks again Re: uplocking reel seat
Posted by:
Donald La Mar
(---.kya.res.rr.com)
Date: December 18, 2015 01:51PM
Bill
The grip inlet diameter and depth for unlocking fly reel seats vary reel seat model to model. Inlet diameter is critical. Depth can be a wee teeny bit too deep an be OK. Your choices are: (1) measure the seat or seats you intend to use and inlet as needed, or (2) buy the correctly sized, pre-inlet rings some reel seat manufacturers and retailers offer. As you intend to make grips in advance and perhaps do not know the correct inlet diameters, you can build up the grips then wait until the reel seats are in-hand to inlet. Just remember to inlet the grips before reaming the grips to fit the blank. I suspect one or more of this sites' sponsors sell a cork inletting tool that will inlet multiple diameters. Re: uplocking reel seat
Posted by:
Phil Erickson
(---.dsl.pltn13.sbcglobal.net)
Date: December 18, 2015 11:37PM
Most of the lighter reel seats are 13/15" or 20mm, the larger ones often are 7/8". I build custom fly rod grips and recess mine to 13/15" and then use a Dremel small sanding drum if I need to enlarge one.
Not sure you will find a market for a Full Wells downlocking, for two reasons: 1.) downlocking reel seats are not as popular and 2.) Those that do use downlocking are usually on lighter rods, where Full wells are less popular. Edited 1 time(s). Last edit at 12/18/2015 11:40PM by Phil Erickson. Re: uplocking reel seat
Posted by:
John E Powell
(---.dynamic.wnyric.org)
Date: January 04, 2016 11:49AM
Comments deleted Edited 1 time(s). Last edit at 09/20/2016 05:10PM by John E Powell. Sorry, only registered users may post in this forum.
|