SPONSORS
2024 ICRBE EXPO |
TM lite and high build mix
Posted by:
Chris Forslund
(---.lightspeed.wlfrct.sbcglobal.net)
Date: March 17, 2014 03:50PM
Has anyone done a 50/50 mix of Tm lite and Tm high build? Meaning like Billy's blend of Prokote and TM. Re: TM lite and high build mix
Posted by:
Rod Churchward
(---.lns20.bne4.internode.on.net)
Date: March 17, 2014 04:46PM
Hi Chris,
No, not exactly that, but I did mix up a batch of TM finish using the lite resin and the high hardener, my excuse is that I'm old. Speaking to the vey helpful chap at RodDancer, Scott, just from memory, his advice was, it shouldn't be done, but if it cures ok, you have gotten away with it. Which it did and I have caught many fish with it over the years, without any problem what so ever. Shoot them an email and ask, you will find them very nice people. Kind regards, Rod. Mboro. Qld. Australia. Re: TM lite and high build mix
Posted by:
Bill Ballou
(---.hsd1.tn.comcast.net)
Date: March 17, 2014 04:46PM
Have done it with ls supreme because the high build was for me too hard to work with. Obviously it gives you a mediun cosistancy. Make sure that you use the same amount of a@ b of each. Should be fine Re: TM lite and high build mix
Posted by:
Chris Forslund
(---.hsd1.ct.comcast.net)
Date: March 17, 2014 04:58PM
Bill Ballou Wrote:
------------------------------------------------------- > Have done it with ls supreme because the high > build was for me too hard to work with. Obviously > it gives you a mediun cosistancy. Make sure that > you use the same amount of a@ b of each. Should be > fine Thanks, I was looking to do 1cc with all 4 bottles. Re: TM lite and high build mix
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: March 17, 2014 05:02PM
Are you trying to thin out the high build ??
They said it should not be done But I thin out flex coat UV high build It works and Well I would think just as long as you mix two of the same A to A or B to B Bill - willierods.com Re: TM lite and high build mix
Posted by:
Scott D parsons
(204.62.140.---)
Date: March 18, 2014 09:50AM
I have heard over the past few months of people doing just what you have asked and done it successfully. I don't recommend Part A from one and B from the other, but if you mix A & B of each separately and then blend them together you should not have a problem.
Thank you for using our products Scott Parsons Scott Parsons 919-900-8998 [www.roddancer.com] [www.fishhawkthreads.com] Re: TM lite and high build mix
Posted by:
Tony Scott
(---.mycingular.net)
Date: March 18, 2014 08:57PM
I have done it many times with great success. As Scott mentioned 1/2 part A and B and 1/2 part A and B. that simple Re: TM lite and high build mix
Posted by:
Chris Forslund
(---.lightspeed.wlfrct.sbcglobal.net)
Date: March 21, 2014 09:52PM
bill boettcher Wrote:
------------------------------------------------------- > Are you trying to thin out the high build ?? > > They said it should not be done But I thin out > flex coat UV high build It works and Well > > I would think just as long as you mix two of the > same A to A or B to B It worked like a charm. And I think I've found a new finish combo. Sorry, only registered users may post in this forum.
|