SPONSORS
2024 ICRBE EXPO |
Rubber or fiber washer cutter?
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: December 17, 2012 01:06AM
Does any one know of a source for a rubber or fiber cutter that could basically cut washers.
I would like to pick up one so that I could use it to create exact sizes for winding checks and similar articles out of unique materials? Sure, you could use two different sized punches, but it would be nice to dial in both the small and large circle at the same time and do the washer punch in one operation? Thanks much for any thoughts or leads on such a product. Roger Re: Rubber or fiber washer cutter?
Posted by:
Ken Preston
(---.hsd1.md.comcast.net)
Date: December 17, 2012 08:34AM
Roger,
I guess you mean something like this? www.toolexperts.com/washer-and-gasket-cutter.html?gclid=CLKOpczGobQCFcqY4Aod6RoAwA Re: Rubber or fiber washer cutter?
Posted by:
Garry Thornton
(---.natsow.res.rr.com)
Date: December 17, 2012 09:44AM
For cutting rings for rod handles etc. I'd look for a cheap hole saw kit at Pep Boy's or Harbor Freight. Re: Rubber or fiber washer cutter?
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: December 17, 2012 01:12PM
I am sorry for not being more clear.
I am looking for a dual cutter that can cut the equivalent of winding checks. Something with a hole range of 1/32 for an inner hole and up to 2 inches for an outer diameter. Neither of these tools would be suitable. Rather, perhaps something like a leather punch for the inner hole and a bigger punch for the outer ring. [www.zorotools.com] and this: [www.google.com] ----------------- These tools may be possible, but I would really like to do this job with one tool rather than two. Roger Re: Rubber or fiber washer cutter?
Posted by:
bill boettcher
(---.dyn.optonline.net)
Date: December 17, 2012 02:23PM
I take it you want to cut these out of metal ??
A leather punch I would not thing would be strong enough What if you tried to contact one of the companies that make winding checks Don't know if they would give any info Maybe you should thing of making these on a lath ?? Just a thought Bill - willierods.com Re: Rubber or fiber washer cutter?
Posted by:
Mark Newcombe
(---.162.dsl.syd.iprimus.net.au)
Date: December 17, 2012 10:11PM
The bittom ones are called wad punches here in aust we use the to make gaskets when we cant find any they work pretty well just place them on the material and give them a solid whack with a nylon hammer or wooden mallet i have a set i baught when i was an apprentice in the mid 80, they are a tool that never wears out. Re: Rubber or fiber washer cutter?
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: December 18, 2012 12:05AM
Mark,
When you use the Wad punches, what do you have the material resting on - when you whack it with the punch? Do you use a hard rubber block, a piece of wood or?? Roger Re: Rubber or fiber washer cutter?
Posted by:
Barry Chapman
(---.41.70.115.static.exetel.com.au)
Date: December 18, 2012 04:09AM
G'Day Roger when you use a wad punches its better to have the material being cut resting on end grain of a piece of hardwood timber then just givethe punch a decent whack with a hammer. I always used a ball pein hammer (always to lazy to get a soft faced one from my tool box) . Regards Baz Bundeena NSW Australia Edited 1 time(s). Last edit at 12/18/2012 04:10AM by Barry Chapman. Re: Rubber or fiber washer cutter?
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: December 18, 2012 10:44AM
Barry,
I like the use of end grain hardwood for a punch backing board. I have tried a bunch of other materials, but the board end up being too hard in the wrong places. The us eof an end grain board should take care of the problem. Thanks again. Roger Re: Rubber or fiber washer cutter?
Posted by:
Barry Chapman
(---.41.70.115.static.exetel.com.au)
Date: December 19, 2012 07:09PM
G'Day roger something like this with a smaller guide attached to locate & center the wad punch might be worth thinking about & wouldn't be hard to make. You wouldn't be able to do it in one hit but it almost becomes one operation.
[www.rodbuilding.org] Regards Baz Bundeena NSW Australia Sorry, only registered users may post in this forum.
|