It has been an awesome year so far at Get Bit Outdoors and we cannot thank you enough for the support!! We are constantly adding new products and have some amazing things instore that will be popping up in the next few months.

We are glad to announce our 'Max Flex' Abalone. [www.getbitoutdoors.com]
Available in 11 HOT! Colors & Two sizes 4.75" x 2.75" and 9.5" x 5.5" to ensure you get the most workable material for your money.

Max Flex was designed specificaly for custom rod builders and may very well be the most flexible abalone on the market. Wtih a thickness of a mere .005 and an industrial grade 3M adhisive backing, it doesn't get any easier. Simply measure, cut, apply a little heat, and you're good to go.

Don't forget about our PacBay Exposed Casting Seat Blowout. [www.getbitoutdoors.com]
These are sharp seats with TiChrome Hoods, at SERIOUS SAVINGS!!

Our Cork Blowout won't last much longer, we've already sold out of 14",8", and 7" grips. We have a handfull of 4" and 6" grips left, with a lot of customers cutting them down for fore grips, split grips etc.... You can't go wrong at these prices but don't wait... when their Gone their Gone!! [www.getbitoutdoors.com]

Tight Lines and Bull's-eyes,

Get Bit Outdoors
407-542-7840
www.GetBitOutdoors.com
www.facebook.com/GetBitOutdoors

And I would guess this is easier then the posts about measuring and getting a large Gap at the seams ????

You have read the posts ???

Bill - willierods.com

We suggest measuring by placing a tape ring around your blank at the 2 points where you want your abalone inlay to start and stop. Cut the tape rings off the blank, they now equal the diameter of the blank at beginning and end of your inlay. We prefer not to worry about the width of the abalone being exact, it is almost impossible to have them meet perfectly so we suggest adding 1/4 to 3/8 of an inch to each measurement. This method will result in an overlap but 'Max Flex' is paper thin and will not be detectable once you've applied your epoxy.

Tight Lines and Bull's-eyes,

Get Bit Outdoors
407-542-7840
www.GetBitOutdoors.com
www.facebook.com/GetBitOutdoors

Get Bit Outdoors.Com Wrote:
-------------------------------------------------------
> It has been an awesome year so far at Get Bit
> Outdoors and we cannot thank you enough for the
> support!! We are constantly adding new products
> and have some amazing things instore that will be
> popping up in the next few months.
>
> We are glad to announce our 'Max Flex' Abalone.
> [www.getbitoutdoors.com].
> html
> Available in 11 HOT! Colors & Two sizes 4.75" x
> 2.75" and 9.5" x 5.5" to ensure you get the most
> workable material for your money.
>
> Max Flex was designed specificaly for custom rod
> builders and may very well be the most flexible
> abalone on the market. Wtih a thickness of a mere
> .005 and an industrial grade 3M adhisive backing,
> it doesn't get any easier. Simply measure, cut,
> apply a little heat, and you're good to go.
>
> Don't forget about our PacBay Exposed Casting Seat
> Blowout.
> [www.getbitoutdoors.com]
> l
> These are sharp seats with TiChrome Hoods, at
> SERIOUS SAVINGS!!
>
> Our Cork Blowout won't last much longer, we've
> already sold out of 14",8", and 7" grips. We have
> a handfull of 4" and 6" grips left, with a lot of
> customers cutting them down for fore grips, split
> grips etc.... You can't go wrong at these prices
> but don't wait... when their Gone their Gone!!
> [www.getbitoutdoors.com]

We are talking .005 in correct.... I saw someone else quote .005mm which would be impossible.. Just making sure im thinking correctly here