SPONSORS
2024 ICRBE EXPO |
Thinning Epoxy
Posted by:
rick brixon
(---.gvllcmtc01.gnvlnc.ab.dh.suddenlink.net)
Date: March 13, 2009 06:34AM
I need a few ideas on how to thin rod finish epoxy or rod building epoxy. I am not sure whether to use denatured alcohol or acetone. I want to thin the epoxy as much as I can without losing the bonding qualities. If you know of a formula or percentage you would be willing to share it would be greatly appreciated. I am trying to join some thin materials and need the epoxy to paint out a larger than normal surface.
Thanks, Rick Re: Thinning Epoxy
Posted by:
Jimi Ellis
(---.hsd1.ga.comcast.net)
Date: March 13, 2009 06:48AM
If you are using decals on your rods, acetone can and usually will ruin them Jimi Ellis Southern Grafix www.SouthernGrafix.com Re: Thinning Epoxy
Posted by:
bill boettcher
(72.251.109.---)
Date: March 13, 2009 08:35AM
I have used a good quality medium drying lacquer thinner, about 3-5 drops per CC of finish. Bill - willierods.com Re: Thinning Epoxy
Posted by:
Tom Kirkman
(Moderator)
Date: March 13, 2009 08:36AM
Epoxy formulators will tell you not to thin your epoxy at all. It can and sometimes does change some of the product's properties.
Flex Coat has often recommended that you use 2 applications and thin the first with a few drops of acetone. ............... Re: Thinning Epoxy
Posted by:
John Krukemeier
(---.dsl.ipltin.sbcglobal.net)
Date: March 13, 2009 08:45AM
I just use heat thin both. Re: Thinning Epoxy
Posted by:
Bill Stevens
(---.br.br.cox.net)
Date: March 13, 2009 09:50AM
I believe the original poster was asking about structural expoxy used to stick things together and not a thread finish. If that is the case do not worry about thinnning the bonding material just apply a thin coat and wipe off excess before clamping the objects together. Re: Thinning Epoxy
Posted by:
Tom Kirkman
(Moderator)
Date: March 13, 2009 10:38AM
Bill,
Thanks, I think you're correct. Rick, In that case it sounds like you're trying to make a little go a longer way. I don't think that's wise. Or perhaps you're just trying to make it more manageable. In the case of the latter, I'd just use a liquid type 2-part epoxy and have the stuff at room temperature before measuring and mixing. You're just going to have to mix up enough to do what needs to be done. ............ Re: Thinning Epoxy
Posted by:
rick brixon
(---.gvllcmtc01.gnvlnc.ab.dh.suddenlink.net)
Date: March 13, 2009 01:21PM
Thank you all for the info - Yes I wanted a little to go a longer way and also thinner would have been easier to paint on. I will just use the product as directed and plug along until the project is finished.
Thanks again Re: Thinning Epoxy
Posted by:
bill boettcher
(---.251.120.242.Dial1.Weehawken1.Level3.net)
Date: March 13, 2009 02:22PM
I never tried to thin out say rod bond or some thing like that. Guess it would work ?
In a closed area would any thing evaporate ?? Bill - willierods.com Edited 1 time(s). Last edit at 03/13/2009 02:28PM by bill boettcher. Re: Thinning Epoxy
Posted by:
Jim Fielding
(69.196.215.---)
Date: March 13, 2009 03:03PM
Not sure what you are attempting to bond, but expoxy formulated for laying up fiberglass is made for rolling or painting out. May or may not be suitable for your particualr application. Re: Thinning Epoxy
Posted by:
Andy Jones
(---.gsp.bellsouth.net)
Date: March 13, 2009 03:55PM
Use a squeegee, edge of credit card, etc to apply the epoxy in a thin even layer for most efficient and uniform coverage. You might be better off using a liquid epoxy vs. a paste epoxy. Sorry, only registered users may post in this forum.
|