SPONSORS
2024 ICRBE EXPO |
Broken Rod - need advice
Posted by:
Pete Kornegay
(---.client.mchsi.com)
Date: September 30, 2006 04:29PM
I need some advice on a broken rod. See photos- Fred's Broken Rod 1 & 3. This is a Rainshadow SWS70L I built for a friend. After a fishing trip at the beach, Fred pulled his boat into a car wash (the type of car wash in which you use a spray wand). He washed down his boat, rods, equipment, etc. to remove salt & sand. Upon arrival at his home, he discovered the rod broken off about 1/4 of the way down from the tip. Fred thinks the rod may have hit something above in the car wash as he drove out but he's really not sure.
The fact that the break occurred just above the guide makes me a little suspicious as to what really may have caused the break. I'm wondering if my guide placement (done by the book) or thread tension or any one of a million other things may have contributed to this breakage. I wanted to post pictures in case any of you breakage veterans might be able to help shed light on what may have happened. The break is somewhat splintered so I'd really be greatful for advice on repair. I plan to rely heavily on notes I took during Ralph O'Quinn's rod repair seminar (Charlotte, 2005) but if anyone can contribute to my first major repair job, I be appreciative. Pete Kornegay Re: Broken Rod - need advice
Posted by:
Rick Marsters
(---.hsd1.ma.comcast.net)
Date: September 30, 2006 05:31PM
Hi Pete,
I am not a rod breakage veteran and I am sure you will get many replies from those that are. I just want to give you my opinion. By viewing the pictures I do not feel that anything done by you in building this Rainshadow SWS70L caused the breakage. The reason for this assumption is the path of the splinter pattern. It looks to me that someone may have accidentally stepped on the rod. There are a few scuffs on the apoxy that tend to lead me to believe the rod rolled under pressure prior to breaking. That is just my own opinion. Again, I am sure you will get a reply from some of the "Pro's" . As far as repair, I found this infomation in the Library within this site. [www.rodbuilding.org] I hope this information helps. Good Health Rick Marsters Re: Broken Rod - need advice
Posted by:
Bill Stevens
(---.br.br.cox.net)
Date: September 30, 2006 05:41PM
Hi Pete! At least he did not tell you it just snapped when he set the hook! I hear that statement almost weekly. The only difference in repair and replace is one has one more letter and ends in an e. It will be an experience to fix the thing and probably will teach you a lot. Do you have any fiber glass pieces that will fit inside th blank. Put the top section between your thumb and forefinger and exert some pressure and roll it close to your ear. Listen carefully for a cracking or popping sound. If you hear something start cleanly cutting off the blank in short sections and repeating the test until you hear no noises. Or better still strip it down and order another blank.
Have a nice tomorrow! Bill Re: Broken Rod - need advice
Posted by:
Jason Alvarado
(---.dc.dc.cox.net)
Date: September 30, 2006 07:19PM
Pete, Whatever fulcrum caused this was probably close to the breakage and made that particular area of the blank a focal point for stress. Imagine holding the rod in both hands and using your knee as the fulcrum then pulling towards you with all your strength, not good. Alot of pressure concentrated instead of distributed throughout. I would not attempt any repair of this blank personally but if you do it would be a great experience for you to share with us. It was a nice build though. Re: Broken Rod - need advice
Posted by:
Billy Vivona
(---.ny325.east.verizon.net)
Date: September 30, 2006 07:58PM
At least he was washing his rods!!! Re: Broken Rod - need advice
Posted by:
Russ Pollack
(---.dyn.embarqhsd.net)
Date: September 30, 2006 10:06PM
I know you can repair this rod. There are several techniques for doing it. The question is, why not just strip off the guides, and use them to build a new one? You'll end up with a little more effort, but a rod I'd trust a whole lot more.
One of the things that happens when a rod breaks is that we all immediately run through a list of questions - how? Why? - etc. If the rod wasn't defective (or at least not definitively provably so), and your build wasn't questionable (i.e., never had one built like that to break before) and the customer even admits that he did something that may be suspect in analyzing what really did happen, then there's nothing to be done except to fix it or replace it. Unless it's a break within 6" of the tip I never volunteer to fix it - just refinish and replace the tip and tip-top, thus making a shorter (and stiffer) rod. ANd if he still wants a true replacement, so be it, but if he knows he broke the rod, even if it was an accident, I'll charge at least the cost of the replacement plus a small bit for the work, butof course nowhere near the original "retail" cost. - just an idea Uncle Russ Re: Broken Rod - need advice
Posted by:
William Bartlett
(---.proxy.aol.com)
Date: October 02, 2006 04:30AM
Pete,
Hate to admit it, but I agree with the above suggestion of just building a new rod. But, if you're sure you want to attempt the repair, follow Ralph's procedure to the letter. It will work, I've restored many old broken rods, for kids to use, using Ralph's techniques with no problems. So far!! YMMV Good Luck!!! Key here is make sure you use a lower modulace section for both the outer and inner sleeve, preferably fiberglass. Oh, and Amen Billy!!!! Bill in WV Edited 1 time(s). Last edit at 10/02/2006 04:32AM by William Bartlett. Sorry, only registered users may post in this forum.
|