SPONSORS
2024 ICRBE EXPO |
Results 1051 - 1080 of 2697
2 years ago
Mark Talmo
1051. Re: Nail knot tip
Thanks, Norman. I am certain Norman and I employ the same method, although we wrap in opposite directions (which is of no ultimate consequence). So there you have it; a respected veteran and an apprentice relying on the same method for trim wraps; it only seems logical it will serve everyone else in between as well.
Forum: rodboard 2 years ago
Mark Talmo
When in need of a precise, clean, crisp hole in cork or composite cork, I use a short, sharpened length of “hobbier’s” brass tubing chucked in my drill/mill or hand drill; very nice results.
Forum: rodboard 2 years ago
Mark Talmo
1053. Re: Nail knot tip
The only real need for employing a nail knot is for the narrow, isolated binding-wraps on bamboo cane blanks, and even then a pull-through loop could be used instead. How many of us are building those? I suppose adding a narrow trim band, AFTER-THE-FACT, to an existing wrap would warrant the use of the nail knot, but how often does that occur? There should not be any after-thoughts when wrapping
Forum: rodboard 2 years ago
Mark Talmo
1055. Re: Nail knot tip
Bob,
CA = cyanoacrylate = commonly known as “Super Glue”.
Tom,
I would think PG, CP (or virtually anything) applied to a portion of regular nylon thread would seal that portion so it would not become translucent as with the remaining, uncoated thread. Am I missing or unaware of something? I am here to learn.
Forum: rodboard 2 years ago
Mark Talmo
1056. Re: Nail knot tip
Michael, Tom and Phil,
If one is using regular nylon thread for whatever desired effect with the suggested nail knot method (or mine for that matter), what “glue” would work?
Forum: rodboard 2 years ago
Mark Talmo
1057. Re: Nail knot tip
Without intending to “one-up” you Michael, similar can be used to produce a single-thread trim band, even stand-alone, isolated from other wraps. Apply CP to a cut length of thread enough for slightly more than one rotation of the blank. Wrap the thread around the blank, aligning the tag ends side-by-side. Wait until the CP is tacky enough (but not cured) to hold the thread in position. Using a f
Forum: rodboard 2 years ago
Mark Talmo
Billy,
It probably would go without being said, but by mixing pigments, one can achieve virtually ANY color. Just remember that a tiny bit of pigment goes a loooooooooooooooooong way!!!
Forum: rodboard 2 years ago
Mark Talmo
Billy,
I use epoxy pigment left over from my composite days. I have heard that Testors hobby paint works if one lets the pigment settle and pour-off the “clear” on top. Others simply purchase “marbling pigment “ available from most rod building supply sources and is designed for use with thread finish epoxies.
Forum: rodboard 2 years ago
Mark Talmo
Billy,
In lieu of a store-bought winding check, create your own radiused filet by building up thread finish tinted with pigment of your color choice; zero gaps, seals against water intrusion, looks and feels very good.
Forum: rodboard 2 years ago
Mark Talmo
Leonard,
In this rod building case, I agree with Roger and Michael = make certain it is very clean, allow it to thoroughly dry and recoat with your favorite thread finish. While there are methods to ensure better bonding of the old and new epoxy, that deals more with structural applications and this is certainly not. I am confident you will be very pleased with a simple recoat of finish.
Forum: rodboard 2 years ago
Mark Talmo
1062. Re: Best Frog Blank?
Andrew,
Why would one want to fish for frogs? lol Sorry, couldn’t resist.
Forum: rodboard 2 years ago
Mark Talmo
1063. Re: Flex Coat Oder?
Tim,
I cannot comment on “older versions” of Flex Coat due to just trying my first batch within the 6 months. I was testing quite a few different thread finishes to discover which performed the best FOR ME. I did notice Flex Coat having more smell to it than the others, but not offensive. As you, I discovered that Flex Coat and ThreadMaster were my preference, but in the thinner versions. When t
Forum: rodboard 2 years ago
Mark Talmo
Kendall,
All of the above replies are valid and deserve to be considered. John additionally added “I also remove some of the tip of the blank. I do this because I do not know how the manufacturer terminated the tip. I cut off just enough (1/16 to 3/16 of an inch) to insure that the tip is flawless and structurally sound.” I have been doing the same with all my blanks, and the butt as well, but
Forum: rodboard 2 years ago
Mark Talmo
Rick,
No one will dispute that Tom and Ron have more experience than I do. Additionally, no one will dispute that epoxy will provide a stronger bond.
That being understood, and even though Ron states “5 minute can be removed with heat”, I only use tip top adhesive (the hot-melt type) to insure the tip top can be removed (if needed) without possible damage to the blank. IT IS MORE THAN STRONG E
Forum: rodboard 2 years ago
Mark Talmo
Kent,
It was my topic and you certainly do not need to apologize; I applaud your injection (so to speak). We all need to keep ourselves and others around amused or life can become a real drag!
Forum: rodboard 2 years ago
Mark Talmo
One thing for sure; when employing such basic or possibly archaic alternatives to the present-day fishing rod/blank, all the hair-splitting simply floats out the window. Ahaaa, the simple (prehistoric) life! That said, it is refreshing to learn some are still thinking-out-of-the-box.
Forum: rodboard 2 years ago
Mark Talmo
Kent,
Thanks for the reply and video link = I GOTTA GET ME ONE OF THEM !!! (the launcher, not the babe!!!)
Forum: rodboard 2 years ago
Mark Talmo
Danny,
I have had a FedEx account for quite a few years = they were a tic cheaper, quicker and possibly more careful with my shipments than UPS. Even with a FedEx account, in the last 2 years I have discovered USPS to be considerably cheaper and quicker yet, hence, have been employing their services. I have never experienced a problem with USPS so I do not know what to say (other than thanks for
Forum: rodboard 2 years ago
Mark Talmo
Russell,
Thank you for the reply which I enjoyed and appreciate. But, honestly, I wouldn’t ask if I didn’t want to learn; the day I stop learning will be the day you read about me in the obituaries! From personal experience, I totally agree with your statement “When you are afraid of a bird's nest it gets into your head and really cuts into your distance”.
And while I may only be 165lb, depend
Forum: rodboard 2 years ago
Mark Talmo
1072. Re: Warped rods
Most “low temp” structural epoxies, assumably including those used by blank manufacturers, respond well to post cures of 150*F. While 180* may be pushing the limit, my gut-feeling is that it would be OK but would be hesitant to go much higher.
Most structures which have been bent, naturally want to return back to zero. However, in this case, I would think the blank would have to be bent slightl
Forum: rodboard 2 years ago
Mark Talmo
Phil,
You have obviously ignored or overlooked MY fly casting stroke lol.
Forum: rodboard 2 years ago
Mark Talmo
Francis,
It only took 18 years of building rods for you to make enough money to retire? I’m jealous!!! Lol Sorry to learn you are giving it up but thanks for helping someone new to the craft.
Forum: rodboard 2 years ago
Mark Talmo
Thank You for the more recent replies as well.
I expected some definite do’s and don’ts, particularly from the fly guys, of which I have very little experience. Properly casting a fly rod must be a passion of persistence, practice and perfection, things to which I am normally attracted. For whatever reason, fly fishing simply never turned-my-crank. While a proper casting technique is required fo
Forum: rodboard 2 years ago
Mark Talmo
Thank you to those replying, both known veterans and names with which I am unfamiliar. Phil, I get your point but you didn’t have to post it 3 times! Lol Hopefully, others will chime-in as well = I am here to learn.
Forum: rodboard 2 years ago
Mark Talmo
1077. Re: Broken rods
Danny,
Searching for as much information as obtainable in the infancy of my rod building, I learned an extremely important rule of which I was previously unaware; NO BLANK IS DESIGNED TO, NOR SHOULD EVER, BE BENT MORE THAN 90* OVER ITS ENTIRE LENGTH. The common term is “high-sticking”. We have all been guilty of doing so, especially when flipping that big, bad boy into the boat. While the blank
Forum: rodboard 2 years ago
Mark Talmo
Colin,
It is indeed refreshing to have someone ask questions, receive helpful replies and then thank those replying. You have approached this build extremely methodically and I am certain it will perform beautifully. Just don’t slam the tailgate on it!!! lol.
Forum: rodboard 2 years ago
Mark Talmo
When casting all three major types of rods, fly, spinning and casting, should the fulcrum / pivot point of the arc be the hand holding the rod or the shoulder of the angler (effectively lengthening the rod)?
(How’s that for a short post of mine? lol)
Forum: rodboard 2 years ago
Mark Talmo
Colin,
You have apparently done your homework, are approaching this build methodically, and yet still ask questions = the sign of a true craftsman.
You have been blessed with Norman’s input and expertise concerning KR setups. I learned two things from his post; in this (your) case, use the 5.5L as the choke guide and move the choke guide out a bit to accommodate progressive spacing throughout
Forum: rodboard |