SPONSORS
2024 ICRBE EXPO |
Results 151 - 180 of 229
11 years ago
Paul Luechtefeld
Can I use #60 madeira for the black. Trying to get good depth.
Forum: rodboard 11 years ago
Paul Luechtefeld
153. Keeping track
Im doing some practice scales fade wrapping and keep losing track what methods do you recommend for not losing your place? For instance I was half way done and noticed one side of the black on one axis was shorter than the rest.
Forum: rodboard 11 years ago
Paul Luechtefeld
155. Re: sanding
Sorry to add this so late but I cant find the gray pads o.ly the green ones would 400 grit sandpaper work or something higher.
Forum: rodboard 11 years ago
Paul Luechtefeld
156. Re: sanding
I messed up on the first coat on the guides had to cut them off I lost 2 of them and had to order more. I am still hopeing
the new ones will come in time to put next coat of finish on before a week has passed. They were micros and I just cant
figure out what happened to them. Thanks for all your replys.
Forum: rodboard 11 years ago
Paul Luechtefeld
157. Re: sanding
Thank you, I,m trying to learn as much as I can as quick as I can.
Forum: rodboard 11 years ago
Paul Luechtefeld
158. Re: sanding
Ok. So why not the green. Just want to know.
Forum: rodboard 11 years ago
Paul Luechtefeld
160. sanding
If I have to wait a week between coats of finish should I sand?
Forum: rodboard 11 years ago
Paul Luechtefeld
161. Re: rod balance
The rod is a 7 and a half foot Phoenix ultralight I only fish for trout and pan fish if I use a longer handle it catches on my coat when I try to fish underbrush and I have to cast side arm. It's a balanced now about 1 inch in front of real seat.
Forum: rodboard 11 years ago
Paul Luechtefeld
162. Re: rod balance
I can't stand a tip heavy rod either but I also don't like long rear grips, 6 inches maximum.I want my rods to balance at the reel stem. I am using burl corck and an aluminum butt cap any other ideas to add weight to bottom of rod. And thank you for your input.
Forum: rodboard 11 years ago
Paul Luechtefeld
163. Re: rod balance
I know there are no hard and fast rules. But was wondering what fisherman prefer but heavy or tip heavy. Most store bought rods seem to balance at the center of the spool.
Forum: rodboard 11 years ago
Paul Luechtefeld
164. rod balance
Where should a spinning rod balance at?
Forum: rodboard 11 years ago
Paul Luechtefeld
Thanks to everyone I am learning so much from this forum.
Forum: rodboard 11 years ago
Paul Luechtefeld
166. Re: Packing
Thanks for the info. I loosened the tension and packed as I went. Worked much better no more slipping and gouging the thread and causing fuzzy's.
Forum: rodboard 11 years ago
Paul Luechtefeld
167. Re: Packing
I may be wrapping too many turns before I try to pack it. I usually go about 30 turn and then pack and I really have to push hard.I use a stainless cuticle tool. I always try to have that little angle where the thread rolls over and drops down on the rod.
Forum: rodboard 11 years ago
Paul Luechtefeld
168. Packing
When packing under wraps how tight is tight enough I keep slipping and making Fuzzy's because I try to pack it it's hard as I can. I already cut it off like 12 times.
Forum: rodboard 11 years ago
Paul Luechtefeld
I think you're right Bill when I was burnishing guide under wraps they came loose to. This is my first time with under wraps I was worried about being able to pack them tight enough so I loosened the tension.
Forum: rodboard 11 years ago
Paul Luechtefeld
I was wondering because i ended my wrap by pulling loop under 5 wraps and when i came back next day it had come loose.
Forum: rodboard 11 years ago
Paul Luechtefeld
171. long underwrap 12"
What do you do when you have to stop in the middle when using hand wrapper.
Forum: rodboard 11 years ago
Paul Luechtefeld
172. Re: marking layout
Thanks Jay, thats what i'm looking for. The most accurate layout I can get. On a bare blank I use a drafters compass with two needle points and make little scratches.
Forum: rodboard 11 years ago
Paul Luechtefeld
173. Re: marking layout
Do you think a sharpie marker would be ok.
Forum: rodboard 11 years ago
Paul Luechtefeld
174. Re: marking layout
Thanks guys, what I am having problems with is making mark on CP covered under wrap.
Forum: rodboard 11 years ago
Paul Luechtefeld
175. marking layout
What do you guys use to mark your layout when you have an underwrap?
Forum: rodboard 11 years ago
Paul Luechtefeld
176. under wrap finish
Still planning my next build. Should I put CP and finish on under wraps before putting on guides and over wrap?
Will be using Madeira thread.
Forum: rodboard 11 years ago
Paul Luechtefeld
177. Re: Guide Set Up
Does the 27 x method apply when using microwave guide system?
Forum: rodboard 11 years ago
Paul Luechtefeld
178. Re: MHX decal
has anyone tried putting scotch tape over the decal before putting it on the rod. I have problems with fingerprints on edge of decal . With scotch tape you could hold on to it while applying the decal and then you could take it off. Was wondering if this would work.
Forum: rodboard 11 years ago
Paul Luechtefeld
179. madeira spool size
how do you get madeira onto spools to fit pac bay handwrapper
Forum: rodboard 11 years ago
Paul Luechtefeld
180. Re: stipper guide
Thank you for all your help. Dont know what i would do without this forum.
Forum: rodboard |