They’re looking good!
Forum: rodboard

Many of the new higher cost rods are using the KR concept or a variation of it. I believe the KR system was introduced in 2019 so prior to KR was NGC? KW guides.
Forum: rodboard

I’d focus more on balance than the amount of space between grips.
Forum: rodboard

The space between grips is up to you..
Forum: rodboard

My process for reel placement (where I hold the reel) is to divide the length of the rod by 8. For example on an 84 inch rod I would place the reel at 10 inches. For overall handle length I divide the length by 6, rounding to the nearest 16th when needed to keep measuring simple. On a 84 inch rod this would be 14 inches. I’ll keep the entire handle assembly (fore grip, reel seat, rear grip, and
Forum: rodboard

I’ve changed guide trains over to the KR system on a few of my factory rods, makes them perform better.
Forum: rodboard

Norman, well said I like learning the history of this stuff. I gather Mike’s just in the never high belly guide camp. I’ve built one high belly guide rod and was sold… my next spinning rod will follow suit.
Forum: rodboard

The diagram is KR recommend guide train for a 10’ light seabass rod, I think it would work for your needs. Use the link and follow the instructions on how to place the guides.
Forum: rodboard

Follow the simple instructions from Fuji… pages 1 and 2.
Forum: rodboard

IMO, the “spine” matters when the rod is under constant load from the lure. I prefer the blank to bend into its natural position during the retrieve. I primarily fish freshwater bass and prefer a spiral wrap for spinnerbaits, chatterbaits, crankbaits, really any lure that puts constant pressure on my wrist, I can definitely feel a difference. Stop-and-go lures (jigs, jerbaits, worms, etc.) I like
Forum: rodboard

I think Tom mentioning that KB guides tend to fail more often than KT’s when used as running guides. When under load the KB’s tend to pull from the wraps. I may have misunderstood but I think that’s what he said.
Forum: rodboard

Use calipers and measure… a #2 is smaller than #3. Guides with rings, measure the outside of the ceramic ring where the ring contacts the metal.
Forum: rodboard

I like to think the spine is the “stiffest” side of the blank. When you roll it and it “pops” in position the spine would be the backside of the bend… like the way a human spine works. I like the way Gary places the guides to counteract the “wobble” effect, increasing the blanks recovery to straight allowing the line less interruption on its travels through the guides.
Forum: rodboard

Practice makes perfect! My builds are far from perfect but get better every time.
Forum: rodboard

A nice 13.5” Tennessee handle work great!
Forum: rodboard

Add tip support, a dab of guide glue, and tightening up your wraps. Keep your hands clean…
Forum: rodboard

Nice build Robert! A stealth bomber!
Forum: rodboard

Carlos- How are you determining those measurements?
Forum: rodboard

Forum: rodboard

Forum: rodboard

Brent- Your recipes are perfect for what you intend to do, stick to it. Don’t let suggestions complicate the process by adding alternatives to what has already been throughly tested. From reading your post it shows you’ve done your homework, the high belly guide is recommended if you intend to use a long leader where the connection knot passes through the guides. When I finally implement this la
Forum: rodboard

Build it! 8+1 is enough guides for a 6’6” spinning rod.
Forum: rodboard

I didn’t see a diagram for a 6’6” rod but this diagram may help a little. - OR - Check out the link below for the KR concept explanation on how to layout the reduction train, choke, and running guides… first couple pages.
Forum: rodboard

Dry-fit everything first and test it out before applying any glue. Tape works great.
Forum: rodboard

What guides are you using? Manufacturers usually suggest a generic spacing.
Forum: rodboard

In my opinion a 9’ 1-4oz medium fast surf blank would be Idea for piers and jetties.
Forum: rodboard

Better appearance with a base layer
Forum: rodboard

My go-to for inshore (trout, reds, and flounder) is the equivalent of the rodgeeks x-comp 7’3” 0 power. It is light enough to enjoy catching trout and strong enough to handle the larger fish.
Forum: rodboard

The first couple pages show how to place the guides manually. This will also dial-in the placement to your particular reel, which is an added bonus.
Forum: rodboard

Cut em’ down, the kids won’t mine the action as they drag them across the concrete, hit trees, and sword fight with them. ;)
Forum: rodboard