SPONSORS
2024 ICRBE EXPO |
Current Page: 1 of 1
Results 1 - 25 of 25
6 months ago
Bob Jordan
Do you want to make shelf pieces or rods to fish with? Most guys I know want a good reliable rod that they trust to fish with.
Forum: rodboard 6 months ago
Bob Jordan
Kids don’t even know want telephone books are today shows how old I am.
Forum: rodboard 6 months ago
Bob Jordan
Once you remove the thread most is off can go over it was a razor blade. Go make it even. I never use a solvent.
Forum: rodboard 6 months ago
Bob Jordan
The first rod I ever done was with telephone books on the table, for tension on the thread. Would put the thread between the pages and ad more books as needed for more tension. Then turn around a chair and lay my hands over it and roll.
Worked good , took a little longer
Then went to rollers on a bench 10’ long
Forum: rodboard 6 months ago
Bob Jordan
How many guys still roll by hand. Once you learn , you can roll pretty fast.
I’ve had my set up for years. My rollers are steel roller skate wheels, that can be moved to fit the wrapping pattern.
What’s your setup.
Forum: rodboard 6 months ago
Bob Jordan
Do you know where I can find them?
I run out of them and can’t find them
OD 3/4”. I D 3/8 or 1/4” I don’t care how long they are .
Forum: rodboard 6 months ago
Bob Jordan
Enjoy the rod , if it gets dirty , use Magic Eraser ? Th cork handles are there, because they feel good.
Forum: rodboard 6 months ago
Bob Jordan
Sand some cork. Get the filings and mix with glue and make a paste. Works good
Forum: rodboard 7 months ago
Bob Jordan
I started building Lamiglas rods years ago, with my buddy . He has this freshwater rod in his hand and shows us how great these Lamiglas rods are. He bends the tip right to the butt. See they don’t break. Turns around and goes go put it in the closet and shuts the door on the tip top. Well, he said they break when you close the door on them .
Forum: rodboard 7 months ago
Bob Jordan
Larry Berkovsky Wrote:
-------------------------------------------------------
> Chucked my 5’ long reamer to my drill press so
> it extended almost to the floor. Got on my knees
> and started reaming a rod handle. Leaned over and
> the reamer grabbed on lock of hair from the top of
> my headed and just like that I had an instant bald
> spot.
Very Funny
Forum: rodboard 7 months ago
Bob Jordan
Like 6 or 7 I like to use a piece of # 10 wire coating , I pull the wire out. I use this instead of a nail Then lay the hollow piece of wire coating on the line. I go abut 6 r 7 turns and then run the mono or braid through the middle of the wire. Then pull the tube ( wire coating ) out. Then start pulling a little on both ends until tight while rolling the middle loops a little with my fing
Forum: rodboard 7 months ago
Bob Jordan
13. Re: Acid wrap
I did not say that line leveling had to do with the spiral wrap. What I said was that the spiral wrap helps the beginner having trouble with keeping his reel straight, Without a level wind reel. Because of the 180° turn , it helps them.
Beginners have trouble with their reels, maybe the weight, or thumb control ? They seem to turn the reel to the side and the line goes to the side of the reel
Forum: rodboard 7 months ago
Bob Jordan
14. Re: Acid wrap
It helps beginners. Did you ever see a newbie use a conventional reel like a jigmaster or a 113H with out a line leveler ? The reel twist on them and the line goes all to one side. Sometimes so bad that they can’t reel the rest of the line in. Happens with kids also. They don’t know how to thumb it.
Forum: rodboard 7 months ago
Bob Jordan
17. Re: Acid wrap
I have used them and build them. Just was looking to see what your thoughts were. I really don’t see too much difference. I’ve been fish for a long time and my thumb works good on leveling the line. I do see it works with beginners, it keeps them from getting all the line on one side of the reel. As far as laying the rod on the gunnel, that’s not good for the rod. That’s my two cents.
Forum: rodboard 7 months ago
Bob Jordan
Why not all D thread, coat underwrap with Lacquer, dries fast and can overwrap within a hour.
Forum: rodboard 7 months ago
Bob Jordan
19. Acid wrap
How and what do you guys think about acid wraps
Forum: rodboard 7 months ago
Bob Jordan
How does Mildrum Carboloy guides fit into your list of guides for hardness
Forum: rodboard 8 months ago
Bob Jordan
22. Wire line
What’s the best guide for wire line
Mildrum Carboloy boat rod guides are getting hard to come by?
Silicon carbide ?
Silicon nitride ?
Thanks bob
Forum: rodboard 3 years ago
Bob Jordan
Blank # 2200 9.
Light yellow in color like Eagle Claw ?
I can’t fine it? Maybe someone knows
Forum: rodboard 4 years ago
Bob Jordan
I don't remember any lamiglas blanks with three numbers?
Andrew what years were they with three numbers thanks bob
Like Dennis Danku said, maybe Harnell
Forum: rodboard
Current Page: 1 of 1
|