I
nternet gathering place for custom rod builders
  • Custom Rod Builders - This message board is provided for your use by the sponsors listed on the left side of the page. Feel free to post any question, answers or topics related in any way to custom building. When purchasing products please remember those who sponsor this board.

  • Manufacturers and Vendors - Only board sponsors are permitted and encouraged to promote and advertise products on the board. You may become a sponsor for a nominal fee. It is the sponsor fees that pay for this message board.

  • Rules - Rod building is a decent and rewarding craft. Those who participate in it are assumed to be civilized individuals who are kind and considerate in their dealings with others. Please respond to others in the same fashion in which you would like to be responded to. Registration IS NOW required in order to post. You must include your actual First and Last name and a correct email address when registering or posting. Posts which are inflammatory, insulting, or that fail to include a proper name and email address will be removed and the persons responsible will be barred from further participation.

    Registration is now required in order to post. You must include your actual First and Last name and a correct email address when registering or posting.
SPONSORS

2022 ICRBE
EXPO ON FACEBOOK
CCS Database
Int. Custom Rod Symbol
Common Cents Info
American Tackle
Anglers Rsrc - Fuji
Back Creek Custom Rods
BatsonRainshadowALPS
Banana River Rods
CRB
HNL Rod Blanks–CTS
CTS New Zealand
Custom Fly Grips LLC
Decal Connection
Flex Coat Co.
Get Bit Outdoors
HFF Custom Rods
HYDRA
Janns Netcraft
Mickel's Custom Rods
My Rod Shop
Mudhole Custom Tackle
MHX Rod Blanks
North Fork Composites
ProProducts
ReelSeatBlanks.com
Renzetti Inc.
Rod Builders Warehouse
RodHouse France
RodMaker Magazine
RodMaker Blog
Schneiders Rod Shop
SeaGuide Corp.
Stryker Rods & Blanks
Tackleworks
The Rod Room
Trondak U-40
Utmost Enterprises
VooDoo Rods

Rod dryer convert to battery operated
Posted by: Andrew Best (---)
Date: January 01, 2022 01:04AM

Working on converting my old rod dryer to a automatic ice fishing jigger. Is it possible to convert to battery operated?
I have at AC 110V 50/60HZ 3.8W 7.5/9 RPM CW/CCW

Re: Rod dryer convert to battery operated
Posted by: roger wilson (---)
Date: January 01, 2022 09:31PM

Andrew,
Just a couple of comments.
Don't do it.
Don't do it.
Don't d0 it.

The reason for my suggestion is that over all of the preceding years, I have built nearly a dozen jiggers for ice fishing and have used them all extensively, in all sorts of weather and for many differences in time of use

Some jigged a small amount. Some jigged a large amount. Some jigged a varying amount. Some jigged for a while, stopped and then restarted at varying intervals.

Since we can use two rods in our area, I would always have one rod with a jig and minnow. The jigger would also have a similar jig and minnow on the end of the line.

Final score.

The rod that was sitting still, or was being held stationary - number of fish out of the hole 323.
The rod that was jigged by one of the many variable jiggers that I used was 0.

One would think that a fish would just run into the jig and minnow on the end of the jigging stick by accident = but no, it never happened.

So, I found a few different fishermen who wanted to try a jigging unit for a rod, and I gave every one of them away.

It wasn't the case that the jiggers did not work the rod. They all worked the rod, some the same, and some quite differently. But the result was the same - no fish caught on a rod that was being held by a jigging machine.

-----------------------------------------------------------------------

However, there was one design that I thought showed some slight sign of promise. This was where the amount of lift drop was changed as a function of the rotation of the motor.

In this case, I used a 12 volt gear motor.;

To the end of the 12 volt motor, I attached a board that with the center of the board on the drill shaft, the board would rotate smoothly and constantly.

Then, in various locations on the board, I installed screws that would be long enough to drill all of the way through the wood disk, and still have a couple of inches of screw rising above the plywood disk.

Then, attached to a rod holding piece of pvc, I attached a lifting arm that would have one end of the lifting arm contact the differently spaced screws as the motor rotated. Since the screws were located at different locations on the board, the lifting arm to the rod holder would lift the rod and the jig different amounts as the motor rotated the plywood disks.

When, I compared the jig lift fall - as seen on my depth finder, the picture displayed on the depth finder was pretty similar to the same jig displayed on the jig and was hand held.

But, the one big difference that I never checked out would be to use a delay timer on the motor itself.

By this I mean that when the timer was off, the disk rotating motor would be off, and the jig would remain stationary Then, when the timer expired, the lifting motor would start cycling, until the timer begin its timing cycle one more time.

This then, would more closely match my standard lift drop, lift drop, lift drop ---- freeze --- lift drop lift drop.

It seemed that the bulk of my time that it was during the freeze sequence on the jig with the jig not moving either up or down when the fish took the bait.

Be safe. If you come up with a good machine and test it and find that it works I would appreciate the overall design and jig sequence that you find works out best for you.

Take care

p.s.
Here is the patent for a jigging machine.
[patents.google.com]

YOu can study the drawings and build what you wish. You will never have a patent infringement suit filed against you if you build a machine for your use only and do not replicate it and sell it to someone. For your use only - no suit filed against you.


Here is a "sullivan jig down" auto jigging machines:
[sullivantipdown.com]

Here is a link to the product: [sullivantipdown.com]

Re: Rod dryer convert to battery operated
Posted by: roger wilson (---)
Date: January 01, 2022 09:50PM

Andrew,
Over the years, I have purchased a lot of
"Surplus parts " to create final products.

Here is a link to a surplus store that sells surplus dc motors.

If you choose one that is 12 volts, you can use juice from your depth finder, or a jumper from your fishing vehicle.

[www.surpluscenter.com]

Sorry, only registered users may post in this forum.
Webmaster