SPONSORS
2024 ICRBE EXPO |
For Roger W- New Power Wrapper Build/Pedal Integration
Posted by:
Dean Posekany
(---.columbus.res.rr.com)
Date: October 05, 2020 04:07PM
Hi Roger,
I've been pouring over the pages of the forum and found this old post and had a few questions if you're willing. "The foot pedal that I use is from a WAH dunlop guitar amp pedal. The reason that I use this pedal is that it allows me to use a standard high quality potentiometer with a gear drive to allow for the full 270 degree potentiometer rotation necessary for 100% control of the DC motor speed controller." I'm in the process building my first power wrapper. I'm using a 24V DC, 180 rpm gearmotor. I have a cheap Amazon speed controller that does a pretty decent job of handling the variable speed requirements and a reversing switch. Where I'm scratching my head is with the foot pedal control. In the post you mention the WAH pedal and I have a few questions. First, I've never physically seen a WAH pedal, but I think I generally understand how they work. Are you gutting the pedal and just using the menchanical pedal and adding your own pot, or are you using the pot function of the pedal? Second, are you feeding the pedal output into your speed controller and bypassing the controller's pot to allow foot operated speed control? Any help or direction you can give would be greatly appreciated. Thanks, Dean Re: For Roger W- New Power Wrapper Build/Pedal Integration
Posted by:
roger wilson
(---)
Date: October 06, 2020 12:28AM
Dean,
Most of the small inexpensive dc speed controllers either use a 10K potentiometer, or 100K potentiometer. It is also important to note, that the requirement on the potentiometer have a linear taper, rather than an audio or logarithmic taper. The speed controls responds correctly when the resistance changes in a smooth linear fashion. Another important specification to note is that the controller have a speed range from 0- maximum voltage, or 0-100% control. There are some controllers on the market that vary the speed from 5% to 90%. If you use a 200 rpm motor and have it slow down to 5%. That would mean that you would only slow a 200 rpm motor down to 10 rpm, which is not what you want, when your lift your foot off the pedal. Essentially, you need a foot controlled device that can vary the resistance of a variable potentiometer from 0 ohms to 10K, or 100K ohms - depending on the controller. If you using a pedal, the normal arc range of a standard foot pedal is about 20 degrees. i.e. if a round potentiometer is connected to a 20 degree pedal, the pedal would only rotate for 20 divided by 270 degrees. This would mean that you would only have a very small speed control range. To eliminate the issue, I chose to use a pedal that uses a rack and pinon design to drive the potentiometer by the use of a rack, or cogged straight shaft connected to the underside of the foot pedal. Then, as the pedal descends from full up, to full down, the rack or cogged shaft will rotate 270 degrees or the full standard rotation of a variable resistor. The pedal type that I like to use is a rock guitar amp pedal called a WAH pedal. These are robust all metal heavy du ty pedals that will stand up to years of service wrapping rods. Here are various examples of NEW Dunlop Wah pedals. [www.jimdunlop.com] Rather than spending the money for a new pedal, and then completely eliminating all of the parts in the pedal with the exception of the rack on the underside of the pedal. I also keep the mounting hardware for the potentiometer. I do not use the potentiometer from the typical WAH pedal, because the typical WAH pedal uses and audio or logarithmic taper that does not provide the control that is needed for the speed controller. However, sometimes one can run across a Linemaster rack and pinion pedal style that is normally used for wire feed welders. The down side of these pedals is that the cost is normally quite high. Also, the design of this pedal resulting in a high foot position fo rthe foot that is placed on the pedal during rod building. It is nice to use a pedal that allows the foot to be quite close to the foot - during normal operation. To find the Dunlop wah pedal in the used category, I check for hits on a pedal search from the local Craigs list. Also, the on line @#$%& sites can sometimes reveal a pedal that is for sale. ------------------------------------------------ By the way, if using only the pedal for control the speed controllers own potentiometer is eliminated and the speed is completely controlled by the foot pedal potentiometer. But, if one wants to use the wrapper for applying finish and to act as an overnight dryer, then it is nice to incorporate the speed controllers own pedal and have a switch such that the variable speed potentiometer that came with the speed controller be used, or the foot pedal that you wish to use to control the speed. The switch essentially uses either the hand dial, or original potentiometer that came with the controller or the potentiometer that is in the foot pedal. Feel free to ask any more questions. Roger Re: For Roger W- New Power Wrapper Build/Pedal Integration
Posted by:
Dean Posekany
(---.columbus.res.rr.com)
Date: October 06, 2020 06:53AM
Thanks, Roger. After that great explanation, I have no further questions. I'll check the ohm range on the the pot in my controller. It does seem to give me a full 0-100% speed control on the gearmotor. I have several dozen pots in my junk/spare parts bin. Hopefully there will be one that matches the controller and will fit a foot pedal.
Now to find the perfect (and cheap) foot pedal. Thanks again. Dean Sorry, only registered users may post in this forum.
|