SPONSORS
2024 ICRBE EXPO |
Presenting rods to customers
Posted by:
Chuck Brezen
(70.97.209.---)
Date: January 27, 2020 07:43PM
Just a quick question... I have never really done anything special when handing over a finished rod to a customer but wondered if you guys have any “special touches” you attach or present the new owner? I feel like I’m handing one of my kids over sometimes after spending so much time together :) thanks for any ideas!
Chuck Re: Presenting rods to customers
Posted by:
Donald La Mar
(---)
Date: January 27, 2020 08:35PM
Chuck
I don't sell rods but do provide rod recipients a document titled Certificate of Origin, The Certificate contains three sections, the first of which is a description of the components (blank, reek seat, grip, guides, finish and adhesives, etc.) and ends with a picture of the rod. The second section describes any blank manufacturer's warranty that is applicable and makes clear I do not provide any warranty, represent suitability for any use, etc. The third and final section is a list of things to do and not to do to care for the rod. Re: Presenting rods to customers
Posted by:
Michael Ward
(---)
Date: January 27, 2020 08:59PM
Idea....
“Rod socks” made of “wire loom” can be made fairly inexpensively and takes maybe 10 minutes to fashion one. I’m looking for a good way to personalize these - I’ve tried using heat press vinyl that is rated for polyester and it does “ok” on the top of the sock where the loom does it stretch out but not so well elsewhere Tried paining it with a stencil and spray paint but it ran bad. I’ve seen them painted and expect they use some type of “stamp” but haven’t figured out how to make my own (Was going to post a pic but not sure how to on this board) Re: Presenting rods to customers
Posted by:
roger wilson
(---)
Date: January 27, 2020 10:33PM
Michael,
If you wanted to personalize the Rod socks, you could have labels made of either a cloth material or possibly a plastic material. Then, just sew the label t the top of the sock where it is flat. take care Re: Presenting rods to customers
Posted by:
Lance Schreckenbach
(---.lightspeed.hstntx.sbcglobal.net)
Date: January 28, 2020 10:28AM
Like handing a kid over to someone who most likely will abuse it. I do a order / data sheet that I make when they order a rod and then re-print it and attach rolled up with a rubber band on the rod in a plastic sleeve. I found these plastic bag sleeves like blanks come in from a rod components merchant. I am more of a "at least get the rod home before you break it" kind of guy so I will make them a pvc tube to put it in with a decal and their name on it for $20. It seems like they really don't like it at first but when they order another rod most of the time they will ask for another one. Those plastic carbon looking weave sleeves are pretty cheap now and I will throw one of those in occasionally to my friends. I guess I am fortunate because many of the people I sell to will tip me also so I wind up getting more than I ask for the rod and really most of them come back and get another one or tell someone else and they buy one. A little extra doesn't hurt anything. Re: Presenting rods to customers
Posted by:
Tom Wewerka
(---.bltmmd.fios.verizon.net)
Date: January 28, 2020 10:35AM
The rod sleeve is a very nice touch but adds cost. What I use is clear plastic sleeve like you find on the blanks when you get them only larger to accommodate both casting and spinning rods. I seal the bottom and fold over the top and staple one of my business cards to it. Most everyone is pleased and can't wait to open it.
[www.mudhole.com] Tom Edited 1 time(s). Last edit at 01/28/2020 02:33PM by Tom Wewerka. Re: Presenting rods to customers
Posted by:
Roger Templon
(---.paw.cpe.atlanticbb.net)
Date: January 28, 2020 02:18PM
I do what Tom W. does. A plastic sleeve is a nice touch that does not cost much. I also include a build sheet that states what components, threads, finishes, etc. were used just in case a repair / duplication is needed and work is to be done by others (out of the area). No cost / pricing info is put on this sheet. I keep a complete list of all related info for the rod in my possession.
Rog Re: Presenting rods to customers
Posted by:
ron zimmerman
(---.tcso.qwest.net)
Date: January 29, 2020 05:12PM
Before I started building rods for myself I had one made by a builder in the Midwest . He didnt even put his name on it and when I told him it wasn't finished because of that he got @#$%& and said all sorts of nasty things to me . I still have the emails . What a turd ! Re: Presenting rods to customers
Posted by:
roger wilson
(---)
Date: January 30, 2020 05:40PM
The one thing that I do with all of my finished rods, is to seal each rod separately in a sealed vinyl sleeve. The sleeve if sealed with an impulse heater.
For example: [www.uline.com] I generally use 2 inch sleeving unless, the size of the guides require 3 inch sleeving. An example of the impulse sealer that I use. [www.uline.com] An impluse sealer works by supplying electrical power to the heater for a given amount of time (impulse). The width of the electrical power impulse determines the amount of total heat that is generated for each push of the button on the sealer. When first starting to use the impulse sealer, several different test seals need to be done - varying the time of the impulse or the width of the electrical power pulse by turning the button on the timer. Then, for ensuing uses of the sealer, the tube is simply inserted onto the sealer bed, the top is pushed down which triggers the pulse. The pulse then heats up for the adjusted amount of time and shuts off. The result is a perfect seal time after time without melting through the bag or not having enough heat to do a very job in completing the seal of the tubing. Take care Sorry, only registered users may post in this forum.
|