SPONSORS
2024 ICRBE EXPO |
Kw stripper guide sizing
Posted by:
Brandon parlacoski
(---)
Date: November 04, 2019 08:56PM
I’m building a north fork st964 9’6” 6-12 casting rod for steelhead/silvers and trying to figure out what size guide to start with I will be using Fuji kw guides. I’m thinking starting with a 12 10 8 6 does this sound about right any suggestions would be great. It seems like there’s tons of info for spinning setups just not a lot for casting.if it helps I’ll be using a revo mgx low pro reel. Thanks in advance Re: Kw stripper guide sizing
Posted by:
Lynn Behler
(---.97.252.156.res-cmts.leh.ptd.net)
Date: November 04, 2019 10:00PM
I would start with a KW10, KW 6, Then whatever runners are sufficient in size to pass any leader knots you may use. No need to step down in sizes. I am not familiar with this particular type of rod, but it sounds pretty fundamental to me. Wait for more opinions. Re: Kw stripper guide sizing
Posted by:
Norman Miller
(---)
Date: November 04, 2019 10:29PM
What kind of casting reel are you planning on using? If a low profile reel a KW 10 (or RV6) is sufficiently high enough and will cast quite well. If you are going to use a casting reel sitting higher off the blanks, then a larger Stripper may be warranted. I have a 9’ Salmon/steelhead casting rod I use with a Curado 201 reel. It has a KW10, and a KW5.5 followed by KB/KT5 runners.
Norm Re: Kw stripper guide sizing
Posted by:
Brandon parlacoski
(---)
Date: November 04, 2019 11:08PM
I will be using a abu Garcia revo mgx very similar in size to your curado. I guess a good question is how does one go about sizing guides for a casting rod.. Re: Kw stripper guide sizing
Posted by:
Spencer Phipps
(---)
Date: November 05, 2019 12:12AM
I see no reason for all the sizes, I'd start with a 10 than 6s on that size rod. Been starting with a ten for near 30 years after fishing than owning the fantastic Berkeley Series One rods. Even the heavy power salmon rod was wrapped that way. Re: Kw stripper guide sizing
Posted by:
Michael Danek
(---.alma.mi.frontiernet.net)
Date: November 05, 2019 08:36AM
I see no reason why the length of the rod would affect guide sizing, although I have seen one article that did take into account the rod length. When I asked why, I didn't get a good answer. The KW sizes recommended for the first guide should work, as will the RV 6 mm, which I prefer. I doubt is there is any significant difference in performance- I just prefer it. The running guides may be all the same size, IMO, and would be sized depending on passing any knots you plan to use. I've settled on 5.5 KB's and KT's. For a rod like this I would consider taking the KB's right to the end to take advantage of its bigger/stronger foot. Re: Kw stripper guide sizing
Posted by:
Jim Ising
(---.dthn.centurylink.net)
Date: November 05, 2019 09:37AM
Brandon, to answer your question in a broader sense, the guides on a casting rod are there to manage the line flow along the blank. Line coming from a casting reel (unlike the coils of a spinning reel) flow pretty smoothly from the spool other than the side-to-side action from the way the line is placed on the spool by the pawl guide going back and forth on the retrieve. The first guide needs to be tall enough and open enough to "choke" the initial burst of line coming from the reel when you cast. You should choose the smallest guide that will do that job and place it where the line does not slap the blank or pile up behind the guide when you cast. The key is the right size in the right place, which comes from trial and error and test casting with guides taped in place. After the crucial placement of the first guide, all other guides can be the same size because the line is now flowing smoothly toward the tip of the rod. It's best to position the remaining guides to provide power during a fight which is called "static loading", you can read about that at [www.anglersresourc.net] Re: Kw stripper guide sizing
Posted by:
Brandon parlacoski
(---)
Date: November 05, 2019 07:11PM
Thanks for all the great answers I really appreciate it. Re: Kw stripper guide sizing
Posted by:
Phil Ewanicki
(---)
Date: November 10, 2019 02:28PM
I have always understood that "stripper guide" refers precisely to the first guide on a fly rod, and the Rodbuilding.Org Glossary of Terms confirms this definition. Maybe it should be changed? Re: Kw stripper guide sizing
Posted by:
Lynn Behler
(---.97.252.156.res-cmts.leh.ptd.net)
Date: November 10, 2019 03:53PM
I believe the proper terminology for rods other than fly is "butt guide". Glad we got that rectified. It was bothering me also to some small extent. Sorry, only registered users may post in this forum.
|