SPONSORS
2024 ICRBE EXPO |
Broken rod
Posted by:
Mark Brown
(---.tic.va.gov)
Date: February 12, 2019 04:43PM
Going to try my first repair. Rod is a 2 piece, slow pitch jigging rod, broke near the handle. Pics uploaded, link below. Costs too much to have rod replaced with warranty. I plan to use a scrap graphite blank of similar diameter for the sleeve (I do not have fiberglass blanks around). Should I approach this by taking the butt cap off or making a clean cut where damaged. I don't think there is a taper at the handle now that I'm thinking of it. So would i build an arbor on the tapered part of the rod to get a good fit with the second piece? It will have very little load or bend at this portion of the rod as the handle is above the break. I've been reading through some of the posts on this issue including the article on rod repair in the forum but still not sure of the approach. Suggestions welcome. Thanks, Mark.
[www.rodbuilding.org] Re: Broken rod
Posted by:
Tom Kirkman
(Moderator)
Date: February 12, 2019 05:38PM
If you use a carbon sleeve you will have an overly stiff spot at the repair. The larger diameter of the sleeve will create more stiffness than the small diameter of the rod blank.
If you are talking about an inner sleeve, carbon will be fine. It should have thicker walls than the blank area you are repairing. ........... Re: Broken rod
Posted by:
Michael Danek
(---.drr02.mskg.mi.frontiernet.net)
Date: February 12, 2019 06:33PM
" It will have very little load or bend at this portion of the rod as the handle is above the break. " It is my opinion that for a break in this region of the rod, a graphite sleeve will work just fine. But you can buy woven glass tubes on line if you want to do it the purest way. The difference because of the location on the rod will be undetectable. Theoretically it will move the balance point rearward, less so with graphite, but still, IMHO, undetectable.
I couldn't get a look at the photo. Please check it out. Re: Broken rod
Posted by:
Norman Miller
(---.lightspeed.jcsnms.sbcglobal.net)
Date: February 12, 2019 06:44PM
I would also do an internal plug repair. Find a blank piece of a similar taper that will fit snuggly into the tip section of the broken rod for several inches. Once you find a piece that fits,take off the butt cap a push this plug into the butt unti it protrudes from the broken area, and now see if the the tip section will still fit snugly and butt up against the end of the butt piece, if it doesn’t you may have to trim and sand a little here and there until you get a snug fit. Then glue in place with a few inches of overlap in each section. I like to wrap the repaired section just to make sure that no splitting will occur. Good luck.
Norm Re: Broken rod
Posted by:
Tom Kirkman
(Moderator)
Date: February 12, 2019 06:50PM
That's how you do it.
......... Re: Broken rod
Posted by:
Mark Brown
(---.hsd1.wv.comcast.net)
Date: February 12, 2019 08:10PM
Thank you all for the suggestions. You guys are always so helpful .Some reason I can not find the pics I uploaded. Anyway, Blank at the handle is not tapered and measures roughly 0.41 inches in diameter. I was thinking whatever plug I used would be tapered and thus present a problem. I'll search elsewhere for a scrap w little to no taper but think I got it. Re: Broken rod
Posted by:
Mark Brown
(---.hsd1.va.comcast.net)
Date: February 12, 2019 08:28PM
So a woven glass tube to just fit snug inside the blank would be good bet? Re: Broken rod
Posted by:
Tom Kirkman
(Moderator)
Date: February 12, 2019 08:39PM
If you're going inside, use carbon.
.............. Re: Broken rod
Posted by:
Mark Brown
(---.hsd1.va.comcast.net)
Date: February 12, 2019 10:45PM
Yes. Going to go inside. Took the but cap off, and inside of blank filled with hardened glue. Is there a trick getting this out without fracturing blank or Do I trim the blank back a few mm ? Thanks again, -Mark Edited 1 time(s). Last edit at 02/12/2019 10:56PM by Mark Brown. Re: Broken rod
Posted by:
Norman Miller
(---.lightspeed.jcsnms.sbcglobal.net)
Date: February 12, 2019 11:29PM
Heat the glue plug with a heat gun or even a hair dryer. Take a drill bit drill into the glue plug and when it heats up pull it out. Heat will soften the glue and you be able to work it out. Since the butt section is short, you could push the plug out using a piece of rod blank coming from the break end. You'll get it out just don't force anything.
Norm Edited 1 time(s). Last edit at 02/12/2019 11:37PM by Norman Miller. Re: Broken rod
Posted by:
Mark Talmo
(71.147.59.---)
Date: February 13, 2019 01:32AM
I have nothing to add to the previous, qualified replies other than making certain the taper, or apparently in this case lack thereof, is precise. You’ll be fine. Fix it, fish it! Mark Talmo FISHING IS NOT AN ESCAPE FROM LIFE BUT RATHER A DEEPER IMMERSION INTO IT!!! BUILDING YOUR OWN SIMPLY ENHANCES THE EXPERIENCE. Re: Broken rod
Posted by:
Mark Brown
(---.tic.va.gov)
Date: February 13, 2019 09:01AM
You guys are the BEST!! That's a great suggestion Norm. Will tackle it tonight. Thanks Re: Broken rod
Posted by:
Seth Johnson
(151.142.219.---)
Date: February 13, 2019 02:20PM
Michael Danek Wrote:
------------------------------------------------------- > " It will have very little load or bend at this > portion of the rod as the handle is above the > break. " It is my opinion that for a break in > this region of the rod, a graphite sleeve will > work just fine. But you can buy woven glass tubes > on line if you want to do it the purest way. The > difference because of the location on the rod will > be undetectable. Theoretically it will move the > balance point rearward, less so with graphite, but > still, IMHO, undetectable. > > I couldn't get a look at the photo. Please check > it out. Can you elaborate on these woven glass tubes and where to get them? Re: Broken rod
Posted by:
Mark Brown
(---.tic.va.gov)
Date: February 14, 2019 10:45AM
Heat gun to the glue plug worked great. Thanks Norm. Now working on a scrap graphite blank to suit as the inner plug. Absence of a taper in the handle a little tricky since all the scraps I have are tapered. I think I got it though. Will get back to work tonight. Thanks everybody. Re: Broken rod
Posted by:
Norman Miller
(---.lightspeed.jcsnms.sbcglobal.net)
Date: February 14, 2019 10:54AM
Happy to hear that! Good luck with the repair.
Norm Re: Broken rod
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: February 14, 2019 05:16PM
For a rod like you are repairing, I would use a piece of solid fiberglass on the inside of the rod of the appropriate size and taper as needed.
Good luck Sorry, only registered users may post in this forum.
|