SPONSORS
2024 ICRBE EXPO |
circular clamps for cork rings
Posted by:
Thom Cherry
(---.lightspeed.lsvlky.sbcglobal.net)
Date: January 02, 2019 01:43PM
I am hoping someone can direct me to a site that sells circular clamps to glue up cork rings Re: circular clamps for cork rings
Posted by:
Spencer Phipps
(172.58.45.---)
Date: January 02, 2019 02:06PM
Are you talking about making rings from pie cut segments? Plastic wire ties work for that. Re: circular clamps for cork rings
Posted by:
Thom Cherry
(---.lightspeed.lsvlky.sbcglobal.net)
Date: January 02, 2019 03:28PM
I have used the ties for years, but several months ago I purchased some circular clamps, but only purchased a dozen. I want to get some more of them, but can't remember the supplier. Which is why I am seeking out other rod builders.
Thanks for the reply Thom Cherry Louisville, KY Re: circular clamps for cork rings
Posted by:
Tom Kirkman
(Moderator)
Date: January 02, 2019 03:42PM
PVC rings, split down one side and sized slightly smaller than the rings, functions well for such clamps.
......... Re: circular clamps for cork rings
Posted by:
roger wilson
(---.hsd1.mn.comcast.net)
Date: January 02, 2019 04:34PM
I would think that a hose clamp would work very well.
[www.zoro.com] Just order the size clamp that would work for you. Re: circular clamps for cork rings
Posted by:
Barry Weaver
(---.hsd1.pa.comcast.net)
Date: January 02, 2019 10:18PM
check out the clamps that JOE has on CUSTOM FLY GRIPS, they work great. Re: circular clamps for cork rings
Posted by:
Barry Weaver
(---.hsd1.pa.comcast.net)
Date: January 02, 2019 10:29PM Re: circular clamps for cork rings
Posted by:
Bill Sidney
(---.gci.net)
Date: January 03, 2019 12:32PM
............. Sorry William Sidney AK Edited 1 time(s). Last edit at 01/03/2019 12:34PM by Bill Sidney. Re: circular clamps for cork rings
Posted by:
Bill Sidney
(---.gci.net)
Date: January 03, 2019 12:32PM
......................... Sorry William Sidney AK Edited 1 time(s). Last edit at 01/03/2019 12:35PM by Bill Sidney. Re: circular clamps for cork rings
Posted by:
Bill Sidney
(---.gci.net)
Date: January 03, 2019 12:33PM
,,,,,,,,,,,,,,,,,,,,,,, SORRY William Sidney AK Re: circular clamps for cork rings
Posted by:
Bill Sidney
(---.gci.net)
Date: January 03, 2019 12:33PM
NOTE there is a tool that will make wire ties tight it is sold at most electronic supply stores , a little costly , but not bad, I did not check Amazon or E bay , but it will make the tie wraps tight an take all the
spaces out if the cork wedges , if you put a plastic shim in the center to help keep the ring of proper alinement a little smaller than 1/4 inch because of cutting loss cause by the with of the saw blade , I got my shim's from LOWE's , any plastic rod will work for the shim [ I think ] [PLASTIC ROD Tightbond will not stick to it ] , William Sidney AK Edited 1 time(s). Last edit at 01/03/2019 12:38PM by Bill Sidney. Re: circular clamps for cork rings
Posted by:
Paul Luechtefeld
(---.mobile.att.net)
Date: January 04, 2019 09:56PM
Barry Weaver Wrote:
------------------------------------------------------- > check out the clamps that JOE has on CUSTOM FLY > GRIPS, they work great. Can these be reused? They look like they would work great and zip ties are single use only. Re: circular clamps for cork rings
Posted by:
Barry Weaver
(---.hsd1.pa.comcast.net)
Date: January 05, 2019 08:33PM
res they can be reused. Sorry, only registered users may post in this forum.
|