SPONSORS
2024 ICRBE EXPO |
A second coat
Posted by:
Morris Elliott
(---.dyn6.twc.com)
Date: August 28, 2018 09:33PM
Can I put a second coat of epoxy over a first coat that is completely cured? Thanks for any help. Re: A second coat
Posted by:
Norman Miller
(---.lightspeed.jcsnms.sbcglobal.net)
Date: August 28, 2018 09:43PM
Yes
Norm Re: A second coat
Posted by:
Morris Elliott
(---.dyn6.twc.com)
Date: August 28, 2018 09:58PM
Thanks Norm! Re: A second coat
Posted by:
roger wilson
(---)
Date: August 29, 2018 12:18AM
But, if you put on enough finish on the first coat you don't need a 2nd coat.
Good luck Re: A second coat
Posted by:
Morris Elliott
(---.carolina.res.rr.com)
Date: August 29, 2018 08:53AM
That would be my problem roger.. seems I didn’t and have a low spot. It’s my 5th rod and I have way so much to learn. Thanks guys for the help Re: A second coat
Posted by:
Lance Schreckenbach
(---.hfc.comcastbusiness.net)
Date: August 29, 2018 12:44PM
Morris,
You can keep putting rod wrapping epoxy over cured epoxy till the cows come home. Most of us apply a thin coat first then go over it with another coat or even 3 to 4+ if you need to. I typically do a thin coat, let it cure, then go over it with a second coat that fills in the thread texture and levels the finish (build up coat). If there are uneven spots I will go over it again. I usually try to do just 2 coats but sometimes you need to do more to make it look right. Tight Lines, Lance Re: A second coat
Posted by:
Morris Elliott
(---.carolina.res.rr.com)
Date: August 29, 2018 02:55PM
Awesome info Lance!! Thanks Re: A second coat
Posted by:
Roger Templon
(---.jst.pa.atlanticbb.net)
Date: August 29, 2018 05:45PM
Morris
I typically apply 2 to 3 coats of lite build finish on every rod I build (I'm up to about 40 rods now). You should be able to apply a second (3rd etc.) within 2 to 3 days of the first coat without any further prep of the finish surface, and maybe even a little longer. I usually wait about 24 hours between coats. Rog Re: A second coat
Posted by:
Morris Elliott
(---)
Date: August 29, 2018 07:02PM
I waited over 24 hours and applied a second coat. I think that will do it. I’ll poat some pics tomorrow. I’m believe I’m more addicted to building rods than I am fishing!!! Thanks again for the help guys. Re: A second coat
Posted by:
roger wilson
(---)
Date: August 29, 2018 07:57PM
I typically do a lot of production builds. i.e. 20-30 rods at a time.
As the saying goes, time is money. So, in order to meet schedules, I typically use only one + coat of high build flex coat for my rods. By doing this, I can coat the rods one morning, and ship them the following morning. When I say 1+ coat, I use the following technique for virtually all of my builds. I have everything ready to go on all of the rods for finish application. I mix up a batch of flex coat and starting from one end, get enough finish on the the butt wraps and the guide wraps to insure a complete fill of the threads. Then, using bright light and magnification, I start from one end, using a heat gun to thin the finish, insure that all bubbles are gone and that the correct amount of finish is one the rod on all locations from the tip to the butt of the rod. While doing this, if I find a thin spot, I will add just a bit of finish and use the heat gun to let the finish flow in with the rest of the finish. Then, after completing one pass, I will do it one more time. This pass typically is nothing more than an inspection pass, but again, if I find a thick or a thin spot, I will take care of it by adding or deleting finish and smoothing finish with the heat gun. At that time, the rod gets transferred to the drum drying with its buddies for an overnight spin on the drum dryer. In the following morning, each rod will be removed from the drum dryer for final inspection and if it passes, will be putt in the shipping rack for packing later in the day. Once in a blue moon, a rod has a problem, and that rod will get fixed in the next batch of rods down the line. But, with only a single 8-12 hour drying cycle, the builds can get out in a timely fashion to meet the expectations and dates for the clients. Good luck Re: A second coat
Posted by:
Morris Elliott
(---.dyn6.twc.com)
Date: August 29, 2018 10:19PM
That was absolutely great info roger!! I’m no where near that kind of production, but I can sure utilize the same technique on one rod. I’ve been using lite pro-kote from midsole, but I have some flex coat I’m gonna try on my next one. Re: A second coat
Posted by:
Roger Templon
(---.jst.pa.atlanticbb.net)
Date: August 30, 2018 07:05PM
Morris
The mention of 40 builds so far is over a period of 14-15 years. No big production shop, just a hobby builder. I have tried a lot of different finishes at one time or another and have settled in on Threadmaster lite as my go to finish. Not because I think it's any better than the others, I have just got used to it's handling properties and I seem to "get away with" with some "things" with this finish that I don't think I would with others. Try several brands and stick with the one that works best for you. The more you use it the better you will get with it! Rog Re: A second coat
Posted by:
Morris Elliott
(---.dyn6.twc.com)
Date: August 30, 2018 10:01PM
Thanks roger! I am going to try flex coat on the next one and see how I like it. The second coat on this one finished it off perfect. I was going to try and post pic but the forum won’t let me (new here and still figuring it out). The info and knowledge here is overwhelming and appreciated by a newby like me. Thanks again all! Sorry, only registered users may post in this forum.
|